Earthbind® products are considered to be environmentally-friendly, bio-based modified asphalt emulsions and are designed to control fugitive dust (Earthbind® 100), stabilize road base materials (Earthbind® Stabilizer), and to recycle reclaimed asphalt pavement and alternative paving (Earthbind® EBS-RA).
Background – Asphalt Cutbacks
Certain asphalt cutbacks have been formally or currently (in limited use) as dust control agents. Asphalt cutbacks are formulated with petroleum solvents and asphalt
There are three types of asphalt cutbacks: rapid curing (RC), medium curing (MC), and slow curing (SC). These cutbacks are named for their rate of curing. Their curing rates are based on the type of petroleum solvent used. For example:
– Rapid curing asphalt cutbacks are formulated with light diluents of high volatility, generally in the gasoline or naphtha boiling point range. The rapid curing cutbacks include RC-70, RC-250, RC-800, and RC-3000. Rapid setting grades are designed to cure quickly and are primarily used for spray applications such as tack coats, aggregate chip seal, and sand seals and similar surface treatments;
– Medium curing asphalt cutbacks are made from diluents of intermediate volatility generally in the kerosene boiling point range. The medium curing asphalt cutbacks include MC-30, MC-70, MC-250, MC-800, and MC-3000. Medium setting asphalt cutbacks are intended for mixing with aggregates;
– Slow curing asphalt cutbacks are formulated with petroleum oils of low volatility generally. The slow curing asphalt
Asphalt cutbacks are rarely used today for dust control. This is due to increasing environmental regulations and concerns by air quality districts throughout the United States. The use of cutback asphalts has been significantly restricted or even prohibited in many parts of theUnited States due to of the high percentages of organic diluents (25-50%).
Earthbind®100, Earthbind® Stabilizer, and Earthbind® EBS-RA were developed as a cost-effective and environmentally-safe alternative for cutback asphalts when used for dust control, prime coats, and recycling reclaimed asphalt pavement/alternative paving.
Summary – Earthbind® vs. Asphalt Cutbacks
– Asphalt cutbacks are formulated with petroleum solvents and are not considered to be environmentally-friendly. In contrast, Earthbind® does not contain any organic solvents or any VOC’s. Earthbind® is considered to be environmentally-friendly.
– Earthbind® 100 was developed in part to provide an alternative to asphalt cutback. Earthbind® does not contain any solvents, naphtha, jet fuel, kerosene, diesel or other volatile compounds that were, traditionally used to”cut” through the dirt and allow the asphalt to stick to the rock.
– Earthbind® 100 is uniquely formulated with proprietary ingredients.Earthbind®® 100 is one of a kind; no other traditional or modified bitumen emulsion is comparable in chemistry and binding capabilities.
– Earthbind® 100 is specifically made to be a dust suppressant. Traditional asphalt emulsions and cutbacks are mainly made for paving-related construction projects instead.
– Asphalt cutbacks such as MC-30, due to the organic solvent, has a longer curing time when compared to Earthbind®. MC-30 usually requires at least3-days to cure (with no traffic on it) whereas Earthbind® can cure in as little as several hours.
– Asphalt cutbacks such as MC-30 can potentially degrade the asphalt pavement applied on top of the prime coat due to the evaporation of the solvent used as the cutter.
– Earthbind® 100 is not considered to be like or the same as the traditional asphalt emulsions which include the “slow sets”, (SS-1, CSS-1,etc.), “medium sets” (MS), “rapid sets” (RS), “quick set” (QS) or “HFemulsions” (HF). For example, Earthbind® 100 is formulated and engineered to be different such as its ability to bond to dust particles and enhance infiltration.
– Earthbind® 100’s base materials are specially chosen and engineered (e.g., viscosity, penetration, etc.) to infiltrate and adequately coat and bond soil particles and aggregates together specifically for dust suppression.
– Earthbind® 100 can be used on “dusty” aggregate when compared to standard asphalt emulsions. When using standard asphalt emulsions, aggregates typically must be clean (washed) to ensure binding.
– Earthbind® 100’s chemistry is non-ionic compared to typical asphalt emulsions that are mostly either cationic or anionic. Therefore, Earthbind® can bind well to all types of soil and aggregates regardless of their ionic charge.
– Earthbind® 100 concentrate is freeze stable meaning it can freeze without breaking or altering the product performance. Standard asphalt emulsions will break when exposed to freezing temperatures.
Earthbind® products are undoubtedly a good choice for dust control and stabilization when compared to other emulsions regardless of whether they are asphaltic, synthetic polymers, etc. Please contact EnviRoad if you would like to learn more about dust control and/or stabilization using Earthbind® 100 and Earthbind®Stabilizer.